Process Control Equipment

Time Electronics manufacture a complete range of process control equipment, designed for pressure calibration, temperature calibration, and loop signal calibration. These well-proven precision test instruments cover the requirements of the process industry.

1048 Voltage / Current / Loop Calibrator		1050 PT100 Simulator (°F)
	Source & Measure Current & Voltage 3 Source ranges 0 - 22mA & 0 - 22V 3 Measure ranges 0 - 70mA & 0 - 50V Transmitter Simulator/Sink Output Steps and Ramps Fine adjustment (Inching) Accuracy 0.02% of span		-100°F to + 1000°F ± 0.5°F accuracy Based on ITS 90 EN60751 23 set points Exceeds Class A Good temperature stability Passive resistance source
1077 Milliamp Transducer and Line Simulator		1090 Temperature and Process Calibrator
	3 Operating modes 100mA Source and Load 24V Line mode 0.02% Accuracy Safety terminals Battery level indicator Portable with protective boot		Measure/Simulate 8 thermocouples Measure/Simulate PT100 Measure/Source (uV/mV/mA) Display in °C and °F 10 point memory recall Inching and Step functions Process loops 4-20mA and 0-50mA
7000 Temperature Calibrator		7005 Loop Calibrator
	Temp Accuracy 0.05 °C (0.09 °F) Temp Resolution 0.01 °C (0.02 °F) Resistance Accuracy 0.03Ω Resistance Resolution 0.01Ω Read & Simulate °C, °F, °K, & Ohms Ramp & Step PT100 plus 7 other RTD types		Loop Source - Current or Voltage Loop Measure - Current or Voltage Loop Current Sink Accuracy 0.01% Resolution 1uA or 1mV Manual Step, Auto-Step and Ramp 20mA drive capability into 1100 ohms
7006 Loop Simulator and 7007 Loop Signal Indicator (LoopMates 1 and 2)		7040 Digital Pressure and Current Calibrator
	4 - 20mA or 0 - 10V loops 7 calibration set-points TxSim and RxTest (Loop-Mate1) RxSim and TxTest (Loop-Mate2) Auto-Step output - adjustable rate Battery powered PP3 Internal loop drive supply		0.2, 2, 5, 10, 20 bar options Pressure/VAC calibration 0.04% acc. Loop current calibration 9 engineering units Min / Max function Leak rate function 4.5 digit display
7010 Single Channel Pressure Calibrator		7015 Dual Channel Pressure Calibrator
	Range options from 0.2 to 600 bar Accuracy 0.04% of full scale Pneumatic or Hydraulic Over- pressure alarm Piezo - resistive pressure sensor Isolated 24/36V loop supply Loop current measure		Range options from 0.2 to 600 bar Accuracy 0.04% of full scale Pneumatic or Hydraulic Over- pressure alarm Piezo - resistive pressure sensor Isolated 24/36V loop supply Loop current measure
7016 Regulated Low Pressure Calibrator		7018 Differential Pressure Calibrator
	Range options from 0.2 to 20 bar Accuracy 0.04% of full scale Pneumatic Over- pressure alarm Piezo - resistive pressure sensor Isolated 24/36V loop supply Loop current measure		Differential range options: 0.2 to 10bar Accuracy 0.04% of full scale Pneumatic Over- pressure alarm Piezo - resistive pressure sensor Isolated 24/36V loop supply Loop current measure
7050 Process and Thermocouple Calibrator		7080 Calibration Bench
	Measure up to 400V, 400mA, 40kΩ Output Volt. up to 10V, 1uV res. Output Curr. up to 20mA, 1uA res. Output Res: 0-400Ω, 0.01Ω res. Thermocouple measure & simulate RTD measure & simulate: PT100 Ramp function		Complete Calibration System Wide range of applications Multifunction Calibrator Module Ideal for process control systems Customer specified modules Internal PC with EasyCal pre-loaded Full lab design available

Process Control Equipment

PDF Downloads